Principles of installing fiber cement floor lumber for building a house (Knock-down house) must understand the details. Floor plank 8 inches 2 points. Floor plank 6 inches. 2 points. Floor plank 4 inches. 1 point.
Note : Read more articles about building a house at trendyhome.co.th
1 MO means not shooting on the verge of 2 cm from the edge. Use a winged drill bit, 7×45 mm long.
Principles of installing fiber cement floors
Firing screws to sink the correct material.
Shot a sinking screw 1-2 mm.
Too many screws popped, wrong.
Too many screws fired, wrong.
Should not be used to make the floor on the 2nd floor. The product is developed as a decorative floor. Not suitable for use on the 2nd floor
The principle of installing 1 fiber cement floor plank is not on the verge of 2 cm from the edge.
In case the floor length is longer than 3 meters, it should be designed to install the floor plank with an alternate connection using screws at the end of the drill with wings, 7×45 mm long.
Do not use it for making floors. Installed higher than the floor level more than 60 cm. or more. In the case of a level higher than 60 cm. must add boards (reinforcement) before laying the floor every time *** for safety in long-term use
Do not use it in wet and wet areas at all times.
Principle of installation of fiber cement board
o arrangement of planks Timber installation work
Overlap 3 cm. for wood plank 6 inches
Overlap 4 cm. for wood plank 8 inches
Shoot the screw 2 cm from the edge. Use a winged screw, 7×25 mm long.
Principle of installation of fiber cement board As the plank is only 3 / 4 meters long, the installation of a wall that is longer than 4 meters must be designed to install alternately, leaving 4 mm. joints. Seal the joints with acrylic sealant.
Principle of installation of fiber cement siding
Cover the cement to cover the outer corner of the house building. Paint the old cement primer + paint over the face. Install with winged screws, size 7 x 45 mm.
Principle of installation of fiber cement cornice
To cut the lotus wood notch 45 degrees, connect to the corner by using a circular saw to adjust the cutting angle at 45 degrees. Shoot the screws at least 2 cm from the edge. Screw spacing 30 – 60 cm. Use a long winged drill bit. 7 x 38 mm. Acrylic sealant for a smooth finish
Principle of installation of fiber cement cornice
To cut the wood notch at 45 degrees, connect to the corner, shoot screws at least 2 cm from the edge.
**Floor lotus work will be installed after painting the ceiling/wall. and finished the floor So bring the lotus floor shoot install later Keep the joint of the cornice and the wall with acrylic sealant.
Principle of installation of fiber cement siding
To cut the wood notch, give 45 degrees to the corner, shoot screws at least 2 cm from the edge. Use wing screws, 7×32 mm. long, for firing over fiber cement boards and steel frames, screw spacing 30-60. cm
Use pointed screws, length 6×38 mm. acrylic sealant make it smooth
Principle of installation of fiber cement eaves
To cut the eaves notch at 45 degrees, connect to the corner by using a circular saw to adjust the angle to shoot screws at least 2 cm away from the edge. Fix 2 screws per point for strength. Screw spacing 30-60 cm. Use screws. Winged drill tip, length 7×32 mm. Acrylic sealant for a smooth finish
Principle of installation of fiber cement eaves Examples of installation work. Timber, cornice, eaves, fiber cement.
Principle of installation of fiber cement slats
1 lumber is not on the verge of shooting, 2 cm from the edge.
Since the lath is only 3 meters long, the installation of the lath longer than 3 meters must be designed to be installed alternately, close-fitting (not plastered), leaving 4 mm. joints. Seal the joints with acrylic sealant. A pile of drill patterns with wings, length 7 x 25 mm.
The principle of installing fiber cement fence 1 MO is not on the verge of 2 cm from the edge. The fence has a thickness of 12-16 mm. There are various lengths. Let us choose to use
1 meter long, cutter head/round head
1.5 m long, cutter head/round head
3 meters long, cutter head
Use a screw with a winged drill bit, length 7×32 mm.
Precautions for installation fiber cement lumber shoot the screw on the verge Must be at least 2 cm from the edge.
Conclusion – How to install fiber cement lumber
1 MO means not shooting on the verge of not less than 2 cm from the edge.
2 TO is to switch, cut the notch into the corner.
1 RO is a distance of 30-60 cm.
Board paint and cement lumber
Paint equipment, paint putty trowel, hard bristle brush, rabbit hair brush, paint roller, oil paint roller No. 80 red sandpaper, sanding machine Chicken Skin Masking Tape Sealant Glue Gun
